How to Read a Peptide COA (Certificate of Analysis)
Published by Purix Lab, a Toronto-based supplier of research peptides. This guide is written for laboratory researchers and is for educational purposes only. All products discussed are for laboratory research only, not for human or veterinary use.
A Certificate of Analysis (COA) is the main document a researcher has for checking that a vial of research peptide matches what’s on the label. A COA can also be the easiest thing in this market to fake. A purity percentage typed into a PDF tells you nothing on its own. The evidence behind it is what counts.
This guide covers each section of a typical peptide COA: HPLC purity, mass spectrometry identity, lot numbers, the testing lab, and test dates. It also lists the red flags that mean a document needs a closer look. We’re a supplier, but we’ve kept this guide neutral so you can apply it to anyone’s paperwork, including ours.
What Is a Peptide Certificate of Analysis?
A peptide COA reports quality-control test results for one specific production batch (lot) of a compound. The lab that ran the tests issues it. That lab may be the manufacturer’s in-house QC lab or an independent third-party lab.
A complete COA usually includes:
- Compound name, and ideally the amino acid sequence and any modifications (for example, C-terminal amidation or acetylation)
- Molecular formula and theoretical molecular weight
- Lot or batch number
- Test date and report/certificate number
- HPLC purity result, with the chromatogram
- Mass spectrometry (MS) result, with observed mass and the spectrum
- Appearance (lyophilized research peptides are usually a white to off-white powder)
- Name, address, and signature of the issuing lab
Keep in mind what a COA can and can’t do. It shows test results for the sample the lab received. It doesn’t promise that a product suits any particular application. It only applies to your vial if the lot numbers match.
Section 1: HPLC Purity — What the Number Means
How HPLC purity is calculated
Peptide purity is almost always measured by reversed-phase high-performance liquid chromatography (RP-HPLC), usually on a C18 column with UV detection around 214–220 nm.
Purity is reported as area percent: the area of the target peptide’s peak divided by the total area of all detected peaks, times 100. A result of “98.7% by HPLC” means the main peak made up 98.7% of the UV signal the detector saw under that method.
What HPLC purity does not tell you
Area-percent purity is a relative figure, which is easy to forget. It does not measure:
- Net peptide content. A lyophilized peptide powder also contains water and counter-ions (often TFA or acetate salts left over from synthesis). A vial can show 99% HPLC purity and still contain well under 100% peptide by weight. Net peptide content needs separate testing, such as amino acid analysis or nitrogen analysis.
- Anything that doesn’t absorb UV at the detection wavelength.
- Identity. A clean single peak shows that one main component dominates. It doesn’t show that the component is the correct peptide. Mass spec answers that question.
How to read the chromatogram
The chromatogram is the real evidence. A purity figure with no trace behind it can’t be checked. On a credible chromatogram, look for:
- Labelled axes: retention time in minutes on the X-axis, absorbance (AU or mAU) on the Y-axis
- One dominant, fairly symmetrical main peak. Heavy tailing, shoulders, or a broad peak can point to impurities or degradation.
- A stable baseline where smaller impurity peaks are visible and integrated, not cut off or left out
- An integration table listing each peak’s retention time, area, and area %. The main-peak percentage should match the purity stated on the COA.
- Method details: column, mobile phase, gradient, flow rate, and detection wavelength
Section 2: Mass Spectrometry — Confirming Identity
HPLC tells you how pure the sample is. Mass spectrometry tells you whether it’s the right molecule. Peptide COAs usually use electrospray ionization (ESI-MS, often coupled as LC-MS) or MALDI-TOF.
Observed vs. theoretical mass
Every peptide has a theoretical molecular weight calculated from its sequence and modifications. The MS section should report the observed mass measured from the sample. For most small and mid-size peptides, the two values should agree within a narrow tolerance, often around ±0.5–1 Da depending on the instrument and method.
Watch for a COA that lists only a theoretical mass, or says “MS: conforms” with no observed value. The theoretical mass is just a calculation from the formula. It isn’t a test result.
Charge states and the spectrum
ESI produces multiply charged ions such as [M+H]⁺, [M+2H]²⁺ and [M+3H]³⁺. A good report shows the spectrum and either labels these peaks or gives a deconvoluted mass. All charge states should work back to the same neutral mass. Small sodium (+22 Da) or potassium (+38 Da) adduct peaks are common. They shouldn’t dominate the spectrum.
Standard intact-mass MS doesn’t confirm residue order and can’t tell some isomers apart. Tandem MS (MS/MS) sequencing does that, though most routine COAs don’t include it.
Section 3: Lot and Batch Number Matching
This step is the simplest one, and people skip it most often. The lot number on the COA must match the lot number printed on your vial. Ideally it also matches your packing slip or invoice and the product page.
- A COA for a different lot tells you nothing about your vial.
- A “representative” or “sample” COA isn’t evidence for the batch you received.
- If a vial has no lot number, you can’t trace it back to any test result.
Section 4: Testing Lab Independence and Verification
In-house vs. third-party testing
An in-house COA comes from the manufacturer’s own QC lab. A third-party COA comes from an independent analytical lab with no stake in the result. Both can be legitimate. Independent testing simply gives an outside check on the manufacturer’s numbers. Accreditation such as ISO/IEC 17025 means the lab’s quality system and competence have been assessed for the methods within its accredited scope.
How to verify a report with the lab
- Find the lab’s name, address, and report number on the COA.
- Look up the lab on your own with a web search. Don’t rely on contact details printed in the PDF.
- Check whether the lab offers a verification portal or QR/report-lookup system. Many independent labs do.
- Contact the lab with the report number and ask them to confirm that the report exists and that its results and lot details match your copy.
- Compare what the lab tells you with the document you have.
If a COA names no lab, or names one you can’t find or contact, treat it as a supplier specification sheet. It isn’t a verified certificate.
Section 5: Test Date and Document Details
- Test date: It should be reasonably recent and make sense alongside the manufacturing date. A test date before the stated synthesis date is a contradiction.
- Report/certificate number: Every real lab report has a unique ID.
- Signature or authorization: Look for a named analyst or QA reviewer and a sign-off date.
Red Flags on a Peptide COA
Look more closely, or ask questions, if you see any of these:
- No report number, no lab name, or no lab address
- Generic COA: one document used across several lots, or across different products
- No chromatogram, or only a cropped main peak with no integration table
- Theoretical mass with no observed mass, or “MS confirmed” with no data
- Identical chromatograms across different lots or products
- Signs of editing: mismatched fonts, misaligned text, blurred or pasted-in sections, copied logos, or PDF metadata that doesn’t fit the issuing lab
- Implausible numbers: round purities repeated on every product, or 99.9%+ with no trace to support it
- Dates that don’t add up, or no date at all
- Lot number missing from the COA or from the vial
- A supplier that won’t answer questions about a document or provide the lab contact
Endotoxin, Sterility and Other Tests
HPLC and MS measure purity and identity. They say nothing about endotoxin levels or microbial contamination. Some research protocols need more data, which may include:
- Endotoxin testing (LAL / Limulus Amebocyte Lysate assay), reported in EU/mg or EU/mL against a stated specification
- Sterility or bioburden testing, where relevant to the material and how it’s supplied
- Residual solvents, counter-ion content (e.g., TFA), or water content (Karl Fischer)
- Net peptide content by amino acid analysis
If your lab protocol calls for any of these, don’t assume they were done. Ask the supplier which tests were run on your specific lot and request the matching reports.
Frequently Asked Questions
What is a good HPLC purity for research peptides?
Many research suppliers specify ≥98%, and some lots test above 99%. The number only means something when the chromatogram supports it and mass spec confirms identity. A well-documented 98.5% is more useful than an unsupported “99.9%.”
Is HPLC purity the same as peptide content?
No. HPLC area-percent shows the relative purity of what the detector sees. Peptide content (net peptide by weight) takes water and counter-ions into account. You need separate testing to measure it.
What does “third-party tested” mean?
It means an analytical lab independent of the manufacturer and seller ran the tests. To check the claim, find the lab’s name and report number on the COA and confirm the report with the lab yourself.
Can a COA from a different batch be used?
Not to evaluate your vial. A COA only applies to the lot it names. Always match lot numbers.
How can I tell if a COA PDF was edited?
Look for inconsistent fonts, misaligned values, low-resolution pasted areas, and metadata that doesn’t fit. The most reliable check is to confirm the report number and results directly with the issuing lab.
Does a COA include endotoxin or sterility testing?
Only when those tests were actually performed and reported. A standard HPLC/MS COA doesn’t cover them. Ask for those reports separately if your research needs them.
About Purix Lab
Purix Lab is a Canadian-owned research peptide supplier with stock held in Toronto. We ship within Canada only, price in CAD, and accept Interac e-Transfer. Batch documentation is available on request; batch-specific reports for current lots are coming soon. If you have questions about lot documentation for any product, email [email protected].
All Purix Lab products are for laboratory research only, not for human or veterinary use.